Wednesday, March 11, 2015

FRUGAL SCRAP IRONING BOARD COVER-TUTORIAL


 photo 1 IRON BOARD_zpsqbb4ehxu.jpg 
My ironing board cover for the small ironing board was looking pretty bad. I use it to put things on like wonder under, stitch witchery and interfacing. I did not want to spend money on new material or use up a larger piece either. I had this really cute material that was given to me. It was not quite wide enough. So put on my thinking cap and came up with an idea to make it work.
 photo 3 IRON BOARD_zps0bomikco.jpg 
I cut off some of the length to add to the sides. To do this I determined where I needed extra width on the ironing board.
 photo 4 IRON BOARD_zpst9osubps.jpg 
Here is a close up of the pieces I sewed together to make the piece of material wide enough.

 photo 6 IRON BOARD_zpsv2fjrw00.jpg
Place the ironing board upside down on the material centering it as best as possible. Make sure that you have enough material all around that you will need to form a seam for the elastic.
 photo 7 IRON BOARD_zpsd9q1bvaj.jpg
Start gently pulling up the material around the front. Pin the material to the front sides to hold it in place.
 photo 10 IRON BOARD_zpsizf3u0kn.jpg
Trim the excess off just above the pinned area.
 photo 12 IRON BOARD_zpsl2scpndr.jpg
Remove the pins and let the material lay flat. Trim the curved edge at the front of the ironing board just like in the picture. It does not have to be perfect as you will be turing this under anyway.
 photo 13 IRON BOARD_zpshuaq9rmr.jpg
Now turn under a seam and pin it to the front of the ironing board so that it will not move as you work your way down the sides of the board.
 photo 16 IRON BOARD_zpsy2spmiw8.jpg
Trim the excess material leaving enough to turn under a seam.
 photo 17 IRON BOARD_zpsq12bmnn5.jpg
This is what it looked like at the end of the ironing board.
 photo 18 IRON BOARD_zps2nymlrvq.jpg
Trim the material leaving enough to turn under a seam that will go over the end of the board, similar to the one that you see on the board.
 photo 20IRON BOARD_zpsax4wnfaq.jpg
Remove the pins and remove the ironing board. ZIG-ZAG the edge or turn under a 1/4 inch seam. Then re-pin a seam allowance that will allow your elastic.
 photo 22 IRON BOARD_zps1dhalm78.jpg
Sew around the edge of your ironing board cover.
 photo 23  IRON BOARD_zpsqmrwnvu6.jpg
Leave an opening to be able to insert the elastic. I use a safety pin to work my elastic through the seam.
 photo 25 IRON BOARD_zpsynemy2fq.jpg
I have a TRICK that I use when running elastic in a long seam. Inside the seam is a small safety pin with elastic. When I want to work the elastic down the seam I pin a diaper pin through the safety pin in the seam. That way my safety pin does not work its way back from the starting point while I am adjusting the elastic.
 photo 26 IRON BOARD_zpshbdx0ujh.jpg
After the elastic is all the way through it should look similar to the picture above.
 photo 27 IRON BOARD_zpshypilvbi.jpg
Put the cover on the board. Centering and adjusting so that the pattern in you material is where you want it.
 photo 29 IRON BOARD_zpsohbz23pw.jpg
Turn your board upside down.
 photo 30 IRON BOARD_zpsihuojchr.jpg
Grab both pieces of elastic and start pulling until the cover is very snug on your board.
 photo 32 IRON BOARD_zpsvdc4gktx.jpg
Carefully tie a knot without letting your elastic become lose.
 photo 33 IRON BOARD_zps3in7jcuo.jpg
I like to tie a lot of knots after the first one just to be sure it does not work itself loose.
 photo 34 IRON BOARD_zpshqr8cpin.jpg
Now I am ready to start sewing again.